Ocean Android devices are one the difficult phones to get their firmware files. Your reading this article definitively means you are looking for a working firmware file for Ocean T10. From this page, you will be able to download 100% working firmware file for Ocean T10. We will also provide you with the flashing procedure for this firmware file.
Similar articles
Ocean Android devices are one the difficult phones to get their firmware files. Your reading this article definitively means you are looking for a working firmware file for Ocean T10. From this page, you will be able to download 100% working firmware file for Ocean T10. We will also provide you with the flashing procedure for this firmware file.
Ocean T10 features
Ocean T10 is and Android MTK device with chip type MT6572? a NanDroid storage type, and runs ON Android 4.4.2 KitKat.
Below are the boot information of this firmware file;
BaseBand CPU :MT6572_S00
BaseBand CPU Secure Version : FF
BaseBand CPU Bootloader Version : 01
----------------------------------------------------
INT RAM: 128 KB SDRAM
EXT RAM: 256 MB DRAM
----------------------------------------------------
NAND: (4Gb+2048Mb) Unnamed Flash
BOOT STYLE : NAND BOOT
Size: 0x20000000 [0.500 GB]
BlockSize: 2048 SpareSize: 64 BMT Blocks 80
Searching partiton table, wait..
[0]Part: PRELOADER Begin: 0x0 Len: 0x100000
[1]Part: PRO_INFO Begin: 0x100000 Len: 0x100000
[2]Part: NVRAM Begin: 0x200000 Len: 0x300000
[3]Part: PROTECT_F Begin: 0x500000 Len: 0x300000
[4]Part: PROTECT_S Begin: 0x800000 Len: 0x300000
[5]Part: SECCFG Begin: 0xb00000 Len: 0x40000
[6]Part: UBOOT Begin: 0xb40000 Len: 0x80000
[7]Part: BOOTIMG Begin: 0xbc0000 Len: 0x600000
[8]Part: RECOVERY Begin: 0x11c0000 Len: 0x600000
[9]Part: SEC_RO Begin: 0x17c0000 Len: 0x40000
[10]Part: MISC Begin: 0x1800000 Len: 0xc0000
[11]Part: LOGO Begin: 0x18c0000 Len: 0x100000
[12]Part: EXPDB Begin: 0x19c0000 Len: 0x200000
[13]Part: FAT Begin: 0x1bc0000 Len: 0x1400000
[14]Part: ANDROID Begin: 0x2fc0000 Len: 0x13600000
[15]Part: CACHE Begin: 0x165c0000 Len: 0x700000
[16]Part: USRDATA Begin: 0x16cc0000 Len: 0x8900000
[17]Part: BMTPOOL Begin: 0xffff0028 Len: 0x0
Offset: 0x1f598000 Count: 18
Advantages of flashing this firmware file
With this firmware file, you can easily fix the following issues on your Ocean T10 device;
- Remove forgotten pattern, pin or password,
- Unbrick your bricked Ocean T10,
- Fix bootloop issues
- Unroot your device to fix bugs which comes as a result of root.
What to note
[*] Always make a backup of your current system before flashing a new one
[*] Flashing any MTK device will require you install the appropriate drivers;- MTK USBVCOM drivers.
[*] After flashing some MTK devices, the IMEI may become invalid/null. You can always fix this issue using guides from this section
[*] Although this firmware file is tested before uploading, we do not guaranty you success after flashing your device with it. So, use this file at your own risk!
Requirements for flashing Ocean T10
Just like any other MTK device, the flashing of Ocean T10 will require these tools/equipment;
- A computer
- A good USB cable
- Android MTK USBVCOM drivers
- Flash tools like SP Flash Tool, Miracle Box, GSM Aladdin Box, NCK Android MTK, etc. Get flash tools from this section
- Firmware file to be flashed. Download from below.
How to flash
Flashing of this firmware file can be done with any MTK flash tool. You could flash with Sp flash tool, GSM Aladdin, or Miracle Box. Since this firmware is a backup made with nck dongle, we will advise you flash using NCK Android MTK dongle.
So, to flash with nck Android mtk dongle version 2.5.6.2, proceed as follows;
- Start by extracting the nck dongle you downloaded from the link above,
- Download also stock firmware from below and extract,
- After you have extracted, run the crack
- In the main dashboard that will open, click on Open scat file to load the firmware scatter file from the saved directory.
 |
| load firmware scat file |
- Navigate to the directory where you extracted the firmware and select the scatter file to be loaded.
 |
| Select and load firmware scat file |
- You show have this result on your nck dongle when you load the firmware scatter file.
 |
| Firmware scat file loaded |
- Now at this point, remove and reinsert phone battery, hit on the Write Flash button, then connect your phone to the PC via USB.
- Once you connect your device via USB, the flashing process should commence. Just sit still and wait for its completion.
 |
| Flashing completed |
COMMENTS