Download Tecno Pouviour 2 LA7 Da file and use it to bypass FRP or when a secure boot file is required during flashing.
Similar articles
Download Tecno Pouviour 2 LA7 Da file and use it to bypass FRP or when a secure boot file is required during flashing.
The Tecno Pouvoir 2 (PIUVOIR2) smartphone released in 2018. It is powered by Mediatek MT6737 chipset, 2 GB of RAM and 16 GB of internal storage.
The Tecno Pouvoir 2 runs on Android OS v8.1 (Oreo) out of the box. It comes with a Li-Po 5000 mAh, non-removable battery. It features a 6 inches IPS display with 720 x 1440 px resolution. The IPS technology is one of the most leading LCD technologies in the world.
Tecno Pouviour Core features
- Model: Tecno LA7
- Platform: Android 8.1 Oreo
- Processor: Quad-core MediaTek MT6737
- GPU: Mali-T720 MP1
- Memory: 2GB RAM
- Colours: Black, Green, Blue, Champagne
- Body Dimension: 159.8 mm x 76.8 mm x 8.5 mm
- SIM Type: Nano SIM
- SIM Count: Dual SIM
- Display: 6.0-inch, IPS LCD capacitive touchscreen, 1440 X 720 pixels
- Rear Camera: 13MP camera, 720p Video@30fps
- Rear Camera Features: Phase detection autofocus, LED flash, Geo-tagging, touch focus, face detection, panorama, HDR
- Front Camera: 8MP camera, 480p Video@30fps
- Built-in Storage: 16GB
- Memory Card Support: Yes, up to 128GB
- 2G GSM: Yes
- 3G WCDMA: Yes
- 4G LTE: Yes
- GPRS: Yes
- EDGE: Yes
- 3G/WCDMA/HSPA: Yes
- HSPA+: 42.2/5.76Mbps
- 4G LTE: Yes
- WLAN: Wi-Fi 802.11 a/b/g/n
- Wi-Fi Hotspot: Yes
- Bluetooth: Yes, v4.2 with A2DP, LE
- USB Port: microUSB 2.0
- SMS/MMS: Yes
- Instant Messaging: Yes
- Push Emails: Yes
- Music Player: MP3/WAV/WMA/eAAC+/FLAC player
- Video Player: MP4/WMV/H.265 player
- FM Radio: Yes
- Loudspeaker: Yes
- 3.5mm Jack: Yes
- Navigation: Yes, with A-GPS
- Maps: Yes
- Accelerometer: Yes
- Proximity Sensor: Yes
- Light Sensor: Yes
- Gyroscope: Yes
- Fingerprint Scanner: Yes, (rear)
- Face Unlock: Yes
- Video Streaming: Yes
- Active Noise Cancellation: Yes
- Image Editor: Yes
- Video Editor: Yes
- Document Viewer: Yes
- Document Editor: Yes
- Battery Capacity: 5, 000mAh nonremovable Li-Po battery
Requirements to use this DA file
- An MTK flash tool like SP flash tool, NCK Box or dongle, Miracle CM2 MTK, Miracle Box, etc.
- Android MTK USBVCOM drivers
- A USB cord
- A computer
Using the DA file
You can import and use this DA file with SP flash tool any other MTK flash tool like NCK Dongle. If you are using NCK dongle, then proceed thus;
- Next, extract and launch the loader of NCK dongle.
- Once it opens, click on the setting tab and load Tecno POP 1 custom DA file from where you extracted.
 |
| loading Tecno LA7 DA file on NCK dongle |
- After loading the DA file, head back to the services tab and click on Reset FRP.
 |
| Click on reset FRP under services |
- At this point after clicking on the "Reset FRP" button, power off your device and connect to the computer via USB.
 |
| Power off the device and connect to the Computer |
- Now with the drivers installed, and your charging circuit working perfectly, NCK dongle should be able to detect your device
- The bypassing process will take only a couple of seconds.
- Once done with the bypassing, you should have a screen like the one below.
 |
| Tecno CC7 frp reset done |
😌 😌 ☺️ After following all the above steps, you must have successfully reset FRP on your Tecno LA7
COMMENTS