Download Tecno Spark 6 Air DA Bin file from here. This Download Agent file will be of great use when bypassing FRP in Tecno Spark 6 Air (KE6/KE6j) and
Similar articles
Download Tecno Spark 6 Air DA Bin file from here. This Download Agent file will be of great use when bypassing FRP in Tecno Spark 6 Air (KE6/KE6j) and also when flashing the stock ROM using some flash tools.
For new Tecno MTK devices, you will encounter many errors using MTK tools. Some of these errors are authentication or buffer errors that comes during flashing a ROM or IMG file. These all errors can be fixed with the help of a secure Download Agent file (DA Bin file).
About the Tecno KE6
Tecno Spark 6 Air (64GB) smartphone was launched on 21st September 2020. The phone comes with a 7.00-inch touchscreen display with a resolution of 720x1640 pixels and an aspect ratio of 20.5:9. Tecno Spark 6 Air (64GB) is powered by a quad-core MediaTek Helio A25 processor. It comes with 3GB of RAM. The Tecno Spark 6 Air (64GB) runs Android 10 and is powered by a 6000mAh battery. The Tecno Spark 6 Air (64GB) supports proprietary fast charging.
As far as the cameras are concerned, the Tecno Spark 6 Air (64GB) on the rear packs a 13-megapixel primary camera with an f/1.8 aperture and a 2-megapixel camera. The rear camera setup has autofocus. It sports an 8-megapixel camera on the front for selfies with an f/2.0 aperture.
The Tecno Spark 6 Air (64GB) runs HIOS 6.2 is based on Android 10 and packs 64GB of inbuilt storage that can be expanded via a microSD card (up to 1000GB) with a dedicated slot. The Tecno Spark 6 Air (64GB) is a dual-SIM (GSM and GSM) smartphone that accepts Nano-SIM and Nano-SIM cards. The Tecno Spark 6 Air (64GB) measures 174.68 x 79.36 x 9.30mm (height x width x thickness) . It was launched in Cloud white, Comet Black, and Ocean Blue colours.
Connectivity options on the Tecno Spark 6 Air (64GB) include Wi-Fi, Bluetooth v5.00, 3G, and 4G with active 4G on both SIM cards. Sensors on the phone include an accelerometer, ambient light sensor, proximity sensor, and fingerprint sensor.
Requirements to use this DA file
- An MTK flash tool like SP flash tool, NCK Box or dongle, Miracle CM2 MTK, Miracle Box, etc.
- Android MTK USBVCOM drivers
- A USB cord
- A computer
Using the DA file
You can import and use this DA file with SP flash tool any other MTK flash tool like NCK Dongle. If you are using the NCK dongle, then proceed thus;
- Next, extract and launch the loader of the NCK dongle.
- Once it opens, click on the setting tab and load Tecno KE6/KE6j custom DA file from where you extracted it.
 |
| loading Tecno KE6/KE6j DA file on NCK dongle |
- After loading the DA file, head back to the services tab and click on Reset FRP.
 |
| Click on reset FRP under services |
- At this point after clicking on the "Reset FRP" button, power off your device and connect to the computer via USB.
 |
| Power off the device and connect to the Computer |
- Now with the drivers installed, and your charging circuit working perfectly, the NCK dongle should be able to detect your device
- The bypassing process will take only a couple of seconds.
- Once done with the bypassing, you should have a screen like the one below.
 |
| Tecno Spark 6 Air KE6/KE6j frp reset done |
After following all the above steps, you must have successfully reset FRP on your Tecno KE6/KE6j
COMMENTS